Anaconda Smelter Stack
Anaconda Copper Mining Company Smoke Stack | |
 Northwest side | |
| Location | Anaconda, Montana |
|---|---|
| Nearest city | Butte, Montana |
| Coordinates | 46°6′36.08631″N 112°54′49.51520″W / 46.1100239750°N 112.9137542222°W[1] |
| Built | 1918 |
| Architect | Alphons Custodis Chimney Constr. Co. |
| NRHP reference No. | 87000607 |
| Added to NRHP | April 9, 1987 |
The Anaconda Smelter Stack is the tallest surviving masonry structure in the world, with an overall height of about 585 feet (178.3 m), including a brick chimney 555 feet (169.2 m) tall and the downhill side of a concrete foundation 30 feet (9.1 m) tall.[2][3][A] It is a brick smoke stack or chimney, built in 1918 as part of the Washoe Smelter of the Anaconda Copper Mining Company (ACM) at Anaconda, Montana, in the United States. A terra cotta coating covered the entire brick chimney when new, but by the time the smelter closed in 1981, most had eroded away except for the upper 40%, exposing most of its bricks and reinforcing rods. The inside diameter at the bottom of the brick chimney is 76 feet (23.2 m) while that at the top is about 60 feet (18.3 m). The stack and its viewing area are now the two-part Anaconda Smoke Stack State Park.[4]
Dimensions
[edit]Brick chimney
[edit]The overall height of the stack is 585 feet 1+1⁄2 inches (178.35 m) (≈ 585 feet),[B] including a brick chimney 555 feet 1+1⁄2 inches (169.20 m) (≈ 555 feet) tall and the downhill side of a concrete foundation 30 feet (9.1 m) high. This was the height when new in 1918, but loss of the terra cotta that covered the top course of bricks since then reduced its height one or more inches. The lowest 68 feet (20.7 m) of the brick chimney is an octagon, the vertices of which point to the cardinal and intercardinal directions, north, northeast, east, etc., while its sides face the secondary-intercardinal directions, north-northeast, east-northeast, etc. Two large vertical openings are in the octagonal portion, each 12.5 by 60 feet (3.8 m × 18.3 m), on its east-southeast and south-southwest sides.[5] When operational, the main flue carried hot exhaust gases to these openings and then into the stack from the smelter which was on the north side of the hill upon which the stack rests.[6] The base of the octagon was 86 feet 7⁄8 inch (26.24 m) (≈ 86 feet) side to side across its bottom before the loss of its terra cotta covering. But the inner surface of the octagon is circular with an inside diameter of 76 feet (23.16 m) (≈ 75 feet) across its bottom. The wall thickness of the octagon at its bottom ranges from 64 inches (1.63 m) (≈ 6 feet) at the center of a side to 102 inches (2.59 m) at each vertex. The rest of the chimney is a slightly tapering cylinder with a top inside diameter of 60 feet 2 inches (18.34 m) (≈ 60 feet) and a wall thickness of 22+1⁄4 inches (0.57 m) (≈ 2 feet) just below a slightly flared top.[3] Its cylindrical portion plus the top 5 feet (1.5 m) of the octagon are encircled by many large steel rods (called bands) for reinforcement. It has had 20 lightning rods around its rim since it was built (which are not included in its height).[7][8] The stack contains 2,464,652 locally manufactured perforated tile bricks, each averaging 2.7 times larger by volume than the size of a normal brick.[7][C] Most are radial bricks that are curved to match a sector of a cylindrical wall. The brick chimney weighs 23,810 short tons (21,600 t).[8][D]
Concrete foundation
[edit]The lowest part of the stack is a concrete foundation or footing that is built on sloped ground with a grade of 21% (12°) because it is just below the top of a hill. It is 30 feet (9.14 m) high above ground at its downhill side and 10 feet (3.05 m) high above ground at its uphill side. It is a hollow octagon, 89 feet (27.1 m) side to side on top and 99 feet 6 inches (30.3 m) side to side across its bottom, 33 feet (10.1 m) high on its downhill side and 21 feet (6.4 m) high on its uphill side, a third of the foundation being below ground. The stepped bottom of the foundation fits the stepped rock formation upon which it rests. The floor of the stack is generally conical leading 17 feet (5.2 m) down below the brick chimney to a 5-by-33-foot (1.5 m × 10.1 m) rectangular grate, then into a 5-foot (1.5 m) square horizontal duct that exits the stack at the center of the downhill side of the foundation on its south-southeast side. This allowed any valuable metal dust particles left in the flue gases that precipitated down to that conical floor to be collected by a car on a track within the duct and sent back to the smelter for more processing.[3]
Construction
[edit]After the concrete foundation was completed in May 1918, construction of the stack began on May 23, 1918 and was completed on November 30, 1918. It was placed into operation on May 5, 1919.[7] It was built by the Alphons Custodis Chimney Construction Company of New York (now Hamon Custodis) under the direction of W. C. Capron, mechanical superintendent of the Washoe Smelting Company.[3][10] Much of the ore the smelter processed after 1955 came from the Berkeley Pit just north of Butte, Montana. At the time it was built, the stack was the tallest masonry, brickwork structure and chimney of any kind in the world and it remains the world's tallest surviving masonry structure.[2] Taller masonry chimneys have existed but have since been demolished. Taller chimneys that still exist are made of reinforced concrete. See List of tallest chimneys.
The Washington Monument would fit inside the stack's brick portion except for their lowest 100 feet (30 m) where an overlap of as much as one foot (0.3 m) at each corner of the monument would occur.[E] The stack's brick portion is about 6 inches (15 cm) taller than the monument's 2015 height.[F] The masonry portion of the stack is about 15 inches (38 cm) taller than the above ground portion of the monument's masonry, which disregards the monument's aluminum apex.[9]
The stack was designed to discharge exhaust gases from the various roasting and smelting furnaces at the smelter. The smelter had a large network of exhaust flues from the furnaces that all fed a main flue, which carried them a half-mile south up the hill to the stack.[6] The flue system and stack combined to provide a natural draft capable of carrying 3–4 million cubic feet (85,000–113,000 m3) per minute of exhaust gases.[12]
State park
[edit]The Washoe Smelter was demolished after its closure in 1981. The stack alone, however, remains standing because the citizens of Anaconda organized to "Save the Stack." It is commonly referred to as "The Stack" or "The Big Stack"[G] and is a well-known landmark in western Montana. In 1986 it was designated the Anaconda Smoke Stack State Park.[13][4] The park has two parts: the Washoe Smelter Stack Viewing Center[14] constructed in 2000 just east of the town of Anaconda and the smoke stack about 1.2 miles (1.9 km) southeast of the viewing area. Although the site of the smelter underwent some environmental cleanup, the general public is not allowed access to the stack itself because the soil around it is still hazardous due to contamination by the toxic metalloid arsenic as well as copper, cadmium, lead and zinc.[15] Terra cotta covered the entire surface of the chimney just as it covered its top;[3] by the time of its closure, the bottom 60% had eroded, including the brick octagon, exposing its bricks and reinforcing rods. The terra cotta is now darker than the exposed bricks.
(southeast side)
(northwest side)
See also
[edit]Notes
[edit]- ^ Only the brick chimney is masonry, not the concrete foundation, because "masonry" must be made of many individual brick, stone, or concrete units, not one continuous mass.
- ^ ≈ means "usually rounded to". Dimensions not so marked are not usually mentioned or rounded.
- ^ Two newspaper sources give different numbers of bricks, 2,464,672[8] and 2,446,392,[9] both of which are probably corruptions of the 2,464,652 number on a plaque in the state park.
- ^ The engineering source[3] mixes dimensions, weight for some material and volume for others, so only approximate weights for the brick chimney and concrete foundation can be calculated from it.
- ^ Although the Washington Monument's side to side width is only 55 feet 1+1⁄2 inches (16.80 m), its diagonal width is √2 greater at 78 feet (23.77 m).
- ^ The Washington Monument's height is 554 feet 7+11⁄32 inches (169.046 m) as measured by the National Geodetic Survey in 2013–14 and reported in 2015 using laser measurements from its peak to nearby ground benchmarks.[11] Its height above ground was reduced in 1975 when a ramp replaced two steps at its base. See Note B in its article.
- ^ The first stack built by the Anaconda Copper Mining Company in Great Falls, Montana, 10 years earlier and 506 feet (154 m) tall, was also referred to as "The Big Stack" (demolished in 1982).
References
[edit]- ^ National Geodetic Survey datasheet RX0934 converted from NAD83 to WGS84 via NGS Horizontal Time-Dependent Positioning
- ^ a b Kelly, John (June 19, 2013). "The Washington Monument is tall, but is it the tallest?". Local. The Washington Post. Retrieved December 26, 2016.
- ^ a b c d e f "Highest Chimney Built for Smelter at Anaconda, Montana". Engineering News-Record. 83 (17): 764–5. October 23, 1919. Retrieved October 1, 2017. Provides precise dimensions via two drawings plus several rounded dimensions in its text.
- ^ a b "Anaconda Smoke Stack State Park".
- ^ National Register of Historic Places – Anaconda Copper Mining Company Smoke Stack. Three good photos.
- ^ a b USGS topoView, → Get Maps → Search by location → Anaconda Montana → Anaconda, MT 1961.
- ^ a b c "Anaconda Co Stack - Anaconda, MT". Waymarking. Blue box contains the words of a plaque entitled "Washoe Stack Facts" at the state park detailing its construction.
- ^ a b c Gibson, Richard (August 28, 2017). "Mining City History: Washoe stack still the world's tallest free-standing masonry structure". Montana Standard. Retrieved October 27, 2017.
- ^ a b Johnson, Carrie (September 2, 2011). "A smokestack tops the monument". Letters to the editor. The Washington Post. Retrieved October 21, 2017. This letter used the monument's unofficial 1999 height measured from a different "architectural zero height point" than its official 2015 height referred to in this Wikipedia article.
- ^ Kidder-Parker Architects' and Builders' Handbook (18th ed.). John Wiley & Sons. 1931. p. 1714.
- ^ National Geodetic Survey, "2013–2014 Survey of the Washington Monument"
- ^ The Anaconda Reduction Works (July 1920 ed.). Anaconda Copper Mining Company. 1920. p. 43.
- ^ "Montana Place Names from Alzada to Zortman". Montana Historical Society Press.
- ^ Washoe Smelter Stack Viewing Site Monuments
- ^ Superfund Site: Anaconda Co. Smelter, Anaconda, MT
External links
[edit]
- Anaconda Smoke Stack State Park Montana Fish, Wildlife & Parks
- Smelter history in brief
- Anaconda Smelter Stack Atlas Obscura
- Revisiting Montana's Historic Landscape
- Superfund Site: Anaconda Co. Selter, Anaconda, MT
46°06′36.58″N 112°54′48.92″W / 46.1101611°N 112.9135889°W
| International | |
|---|---|
| National | |
- Chimneys in the United States
- Industrial buildings completed in 1919
- Towers completed in 1919
- Industrial buildings and structures on the National Register of Historic Places in Montana
- Protected areas established in 1986
- State parks of Montana
- Protected areas of Deer Lodge County, Montana
- National Register of Historic Places in Deer Lodge County, Montana
- 1918 establishments in Montana
- Anaconda Copper