Loading...
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 | /* * ethtool.h: Defines for Linux ethtool. * * Copyright (C) 1998 David S. Miller (davem@redhat.com) * Copyright 2001 Jeff Garzik <jgarzik@mandrakesoft.com> */ #ifndef _LINUX_ETHTOOL_H #define _LINUX_ETHTOOL_H /* This should work for both 32 and 64 bit userland. */ struct ethtool_cmd { u32 cmd; u32 supported; /* Features this interface supports */ u32 advertising; /* Features this interface advertises */ u16 speed; /* The forced speed, 10Mb, 100Mb, gigabit */ u8 duplex; /* Duplex, half or full */ u8 port; /* Which connector port */ u8 phy_address; u8 transceiver; /* Which tranceiver to use */ u8 autoneg; /* Enable or disable autonegotiation */ u32 maxtxpkt; /* Tx pkts before generating tx int */ u32 maxrxpkt; /* Rx pkts before generating rx int */ u32 reserved[4]; }; /* these strings are set to whatever the driver author decides... */ struct ethtool_drvinfo { u32 cmd; char driver[32]; /* driver short name, "tulip", "eepro100" */ char version[32]; /* driver version string */ char fw_version[32]; /* firmware version string, if applicable */ char bus_info[32]; /* Bus info for this interface. For PCI * devices, use pci_dev->slot_name. */ char reserved1[32]; char reserved2[28]; u32 regdump_len; /* Amount of data from ETHTOOL_GREGS */ }; #define SOPASS_MAX 6 /* wake-on-lan settings */ struct ethtool_wolinfo { u32 cmd; u32 supported; u32 wolopts; u8 sopass[SOPASS_MAX]; /* SecureOn(tm) password */ }; /* CMDs currently supported */ #define ETHTOOL_GSET 0x00000001 /* Get settings. */ #define ETHTOOL_SSET 0x00000002 /* Set settings, privileged. */ #define ETHTOOL_GDRVINFO 0x00000003 /* Get driver info. */ #define ETHTOOL_GREGS 0x00000004 /* Get NIC registers, privileged. */ #define ETHTOOL_GWOL 0x00000005 /* Get wake-on-lan options. */ #define ETHTOOL_SWOL 0x00000006 /* Set wake-on-lan options. */ /* compatibility with older code */ #define SPARC_ETH_GSET ETHTOOL_GSET #define SPARC_ETH_SSET ETHTOOL_SSET /* Indicates what features are supported by the interface. */ #define SUPPORTED_10baseT_Half (1 << 0) #define SUPPORTED_10baseT_Full (1 << 1) #define SUPPORTED_100baseT_Half (1 << 2) #define SUPPORTED_100baseT_Full (1 << 3) #define SUPPORTED_1000baseT_Half (1 << 4) #define SUPPORTED_1000baseT_Full (1 << 5) #define SUPPORTED_Autoneg (1 << 6) #define SUPPORTED_TP (1 << 7) #define SUPPORTED_AUI (1 << 8) #define SUPPORTED_MII (1 << 9) #define SUPPORTED_FIBRE (1 << 10) /* Indicates what features are advertised by the interface. */ #define ADVERTISED_10baseT_Half (1 << 0) #define ADVERTISED_10baseT_Full (1 << 1) #define ADVERTISED_100baseT_Half (1 << 2) #define ADVERTISED_100baseT_Full (1 << 3) #define ADVERTISED_1000baseT_Half (1 << 4) #define ADVERTISED_1000baseT_Full (1 << 5) #define ADVERTISED_Autoneg (1 << 6) #define ADVERTISED_TP (1 << 7) #define ADVERTISED_AUI (1 << 8) #define ADVERTISED_MII (1 << 9) #define ADVERTISED_FIBRE (1 << 10) /* The following are all involved in forcing a particular link * mode for the device for setting things. When getting the * devices settings, these indicate the current mode and whether * it was foced up into this mode or autonegotiated. */ /* The forced speed, 10Mb, 100Mb, gigabit. */ #define SPEED_10 10 #define SPEED_100 100 #define SPEED_1000 1000 /* Duplex, half or full. */ #define DUPLEX_HALF 0x00 #define DUPLEX_FULL 0x01 /* Which connector port. */ #define PORT_TP 0x00 #define PORT_AUI 0x01 #define PORT_MII 0x02 #define PORT_FIBRE 0x03 #define PORT_BNC 0x04 /* Which tranceiver to use. */ #define XCVR_INTERNAL 0x00 #define XCVR_EXTERNAL 0x01 #define XCVR_DUMMY1 0x02 #define XCVR_DUMMY2 0x03 #define XCVR_DUMMY3 0x04 /* Enable or disable autonegotiation. If this is set to enable, * the forced link modes above are completely ignored. */ #define AUTONEG_DISABLE 0x00 #define AUTONEG_ENABLE 0x01 /* Wake-On-Lan options. */ #define WAKE_PHY (1 << 0) #define WAKE_UCAST (1 << 1) #define WAKE_MCAST (1 << 2) #define WAKE_BCAST (1 << 3) #define WAKE_ARP (1 << 4) #define WAKE_MAGIC (1 << 5) #define WAKE_MAGICSECURE (1 << 6) /* only meaningful if WAKE_MAGIC */ #endif /* _LINUX_ETHTOOL_H */ |